Video Description
Follow this quick video and step-by-step checklist to install Bali Cordless Tailored Roman Shades. You’ll place and level the brackets, snap the headrail into place, attach the lift handle, and run a smooth first operation—no cords required. Use this guide for both inside mount and outside mount installations.
Why Tailored Romans? Crisp, structured folds bring a clean, designer finish to any room. Go inside mount for a built-in look, or outside mount for added overlap and better edge light control.
What’s in the Box (Typical)
- Fabric shade pre-attached to headrail (cordless lift)
- Mounting brackets (left/right) + center support for wider widths
- Mounting screws; optional valance/end caps (model dependent)
- Bottom-rail handle (clips on at center)
Tools You’ll Need
- Tape measure, pencil, level, step stool
- Drill/driver with 1/8" (3 mm) bit, Phillips bit
- Appropriate anchors for your surface (wood, drywall, masonry)
- Safety glasses
Before You Start
- Inside mount: Confirm minimum recess depth and dry-fit the headrail to check clearance around locks/trim.
- Outside mount: Plan at least 1–2" overlap per side (more for darker rooms) and extra height for the headrail/valance.
- Bracket plan: Mark bracket faces so they’re co-planar (same height and plane) for a smooth snap-in.
Inside Mount — Step-by-Step
- Mark & pre-drill: Center the headrail in the opening and mark bracket locations level. Pre-drill with a 1/8" bit if needed.
- Install brackets: Fasten left/right brackets (add center support if provided). Keep bracket faces aligned on a single plane.
- Seat the headrail: Hook the headrail lip onto the bracket tabs (front or rear per bracket style), then rotate until each bracket clicks closed. Run your hand along the rail to confirm full engagement.
- Attach the handle: Clip the handle at the center of the bottom rail for even, level lifting.
First Run & Leveling
- Operate from center: Lift and lower with two hands at the center of the bottom rail for level travel.
- Equalize: Run 2–3 full up/down cycles to balance the cordless mechanism.
- Tilt fix: If one side sits higher, re-seat the headrail (ensure every bracket is locked), center the handle, and cycle again.
Light, Privacy & Finishing Touches
- Inside mount: Expect small side light gaps—normal for shades.
- Outside mount: Increase overlap for better darkness; consider side panels to frame the window and mask gaps.
- Fabric relaxation: Let the shade hang fully lowered for 24–48 hours so folds relax after shipping.
Care & Cleaning
- Dust with a microfiber duster; vacuum gently with a brush attachment.
- Spot-clean lightly with mild soap and water; test in an inconspicuous area first.
Troubleshooting
- No “click” when mounting: Brackets may be out of plane. Re-level and press the headrail firmly until each bracket clicks.
- Uneven lift (cordless): Operate from the center; confirm all brackets are fully latched; run several full cycles.
- Fabric rubs trim (outside mount): Add spacer blocks or shift bracket positions slightly to create clearance.
Need to compare colors or linings for other rooms? Request free swatches to see how fabrics look in your lighting. Shop all of our Bali custom tailored Roman shades
Bali Cordless Tailored Roman Shades — FAQs
What’s the minimum depth for an inside mount Roman shade?
Minimum recess depth varies by headrail style. Check your product sheet; if depth is limited, a partial recess will work but the headrail may project slightly beyond the frame.
Do I need a center support bracket?
For wider headrails, yes—a center support prevents flex and keeps the shade operating smoothly. Seat side brackets first, then snap the center support last to keep everything co-planar.
Why does my shade lift unevenly after install?
Operate from the center with two hands and cycle the shade fully a few times to balance the cordless spring. Also confirm all brackets are locked and the handle is centered on the rail.
Can I steam out shipping wrinkles in the fabric?
First, let the shade hang fully lowered for 24–48 hours to relax. If needed, use a cool iron/garment steamer with a pressing cloth and light passes only—avoid direct heat on trims or liners and test a hidden area first.
Need more choices? Shop our entire line of quality Bali window treatments
